reshape_array uses text_version to reload the container content,
so make sure it is available.
Signed-off-by: Marcin Labun <marcin.labun@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Only one spare is passed in update.
When more than one disk is added first spare is passed multiple times.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Slot was set based on anchor information.
Disks information was copied outside disk list area.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
load_super tries to load container first anyway but if it fails
eg. after physically removing a disk
then it tries to read metadata from container device.
This will always fail and print confusing errors.
So use load_container instead of load_super on container.
On failure to read metadata we should skip this array.
It will be dealt with the next time round.
Signed-off-by: Anna Czarnowska <anna.czarnowska@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add disks fails due to empty sys name field.
sysfs_init fills out required fields for add disk operation.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
To reshape a RAID0 we convert to RAID4 first. This makes it look
like it could be degraded and so we are tempted to ensure there are
enough spares. However this is not appropriate for RAID0, so
explicitly exclude new_level == RAID0 in this check
Reported-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Based on status information disks are added to array during grow (in reshape_array()).
This information currently is not present and all disks (old and new) were added to md.
To avoid adding already present disks, disk.state has to be set.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Child_monitor was design to perform 'manage_reshape' for native
arrays. So change the signature for ->manage_reshape to match
child_monitor and move the all to the same place that child_monitor
is called from.
Also give super-intel a manage_reshape handler which simple calls
child_monitor.
Signed-off-by: NeilBrown <neilb@suse.de>
child_monitor has overall responsibility for backups using the generic
bsb, so move all handling under it's control.
signed-off-by: NeilBrown <neilb@suse.de>
We currently suspend rather large sections of
the array which can take a while to process.
Possibly smaller sections are better. Possibly it should be
adjusted on a timeout basis.
Signed-off-by: NeilBrown <neilb@suse.de>
The array might not be a multiple of the chosen backup size, so
the last bit to be backed up might be a bit smaller. Handle that
correctly.
Signed-off-by: NeilBrown <neilb@suse.de>
At some points we need to perform 2 backups at once so as to
start the 'double buffering' approach. So rather than assuming
what the next backup should be, example suspend_point and backup
as much as possible up to there.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ We need to clean up the backup file after the reshape finishes.
2/ We need to remove the suspended region and clear the resync
controls after the resync finishes.
Signed-off-by: NeilBrown <neilb@suse.de>
The array_size we need to consider is the largest possible size of the
array, which is a different calculation depending on whether the array
is growing or shrinking.
Signed-off-by: NeilBrown <neilb@suse.de>
'sync_completed' can sometimes have a value which is slightly high.
So round-down relevant values to new-chunk size and that is what we
want.
Subtract from component_size after scaling down rather than before as
that is easier.
Make sure max_progress never goes negative when reshaping backwards.
Signed-off-by: NeilBrown <neilb@suse.de>
The current code is right.
Instead compute where we might eventually need to back up to, and
then compare that to how far we have progressed.
Also move suspend_point up towards where we might need to backup to,
rather than just as far as max_progress - as max_progress can never
exceed where we are currently suspended to.
Signed-off-by: NeilBrown <neilb@suse.de>
It isn't needed as we always work in multiples of full
destination stripes.
Also multiply by 'after' disks, not before.
We can progress until the point we would write then lines up with
where we would read now.
We read now from
array-address: reshape_progress device-address: read_offset
So we write then to
device-address: read_offset array-address: read_offset * after.disks
Signed-off-by: NeilBrown <neilb@suse.de>
The 'blocks' number computed by analyse_change is the number of
blocks that it makes sense to back-up at a time.
It is the smallest number of blocks that is a whole number of
stripes in both the old and the new layout.
However we are also using it as the smallest amount of progress
that can be made at a time, which is wrong as it is always valid
to progress a single stripe in the new layout.
So change 'blocks' to be called 'backup_blocks' to make it more clear.
And pass new_chunk size down so it can be used for 'minimum forward
progress' calculations.
Also set 'stripes' (the amount actually backed up) from the
possibly-scaled 'blocks' number rather than ignoring it and using
backup_blocks.
Finally, get rid of 'read_range' as it isn't used (or needed).
Signed-off-by: NeilBrown <neilb@suse.de>
Once we have called reshape_container or reshape_super we have handed
on the responsibility for unfreezing the array, so Grow_reshape
shouldn't call unfreeze.
Signed-off-by: NeilBrown <neilb@suse.de>
When converting to RAID6, the new layout should match the old
layout, not the RAID6 version of the old layout.
Signed-off-by: NeilBrown <neilb@suse.de>
We want start_reshape to work no matter what the current values
of suspend_lo/suspend_hi are. So initialise suspend_lo very high
as this allows suspend_hi to be set to anything.
Signed-off-by: NeilBrown <neilb@suse.de>
When raid0 array is takeovered to raid4 for reshape it should be possible to detect
that array for reshape is monitored now for metadata update.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
As raid4 is not supported by imsm (this is takeovered raid0)
do not fix degraded raid4 arrays.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After raid0 reshape is finished backward takeover has to be executed.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For level migration support it is necessary to allow mdmon to react for level changes.
It has to have ability to change configuration of active array,
and for array level change to raid0 finish array monitoring.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When raid0 reshape is performed metadata has to be applied by mdadm.
(without mdmon)
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For code reuse in raid0 reshape case when monitor is not loaded.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When user wants to add spares to container with raid0 arrays only
it is not possible to update metadata due to lack of running mdmon.
To allow for this direct metadata update by mdadm is used in such case.
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When second array reshape is about to start metadata should be updated
by mdmon in imsm_set_array_state().
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When new disks are added array size has to be set by mdadm as array grows.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When disks are added size has to increase in metadata.
This size should be used by common code to set size in md when reshape will be finished.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For general migration function blocks_per_migr_unit() has to return valid value.
If there is no valid return, 0 is returned instead and causes division by 0 error.
Additionally guard in function was added for such case.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When reshape is finished monitor calls set_array_state() and finishes migration in metadata.
This change allows for finishing metadata migration on reshape end.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For external metadata parameters has to be changed via sysfs.
i.e. change of raid_disks requires handshake mdmon<->md (md_allow_write())
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add support for reading volume information during migration process.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
During first metadata update imsm for compatibility reason should update
only one array.
Buffers in prepare_update() are prepared for second update as well.
Signed-off-by: NeilBrown <neilb@suse.de>
Metadata is not modified by metadata preparation handler.
It has to be read again from array.
There is 2 read required:
1. before 'for' entry to get updated information after reshape_super() call
2. inside 'for' loop to get updated information for every processed array
(it can happen /i.e. imsm case/ that container operation is a set of array operations
and information in metadata is changed after every loop).
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Meta data was not updated due to the following problems:
1.disk index < 0 was treated as invalid, but this is spare device
2. disk index greater than currently used disks is correct also
3. newmap pointer has to be refreshed for second map copy operation
4. size calculation has to be guarded for shrinking operation
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When container operation is not allowed user has to get proper information on console about it
Currently this information was displayed as debug info only.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Correct information displayed by '-E' option.
1. FIX: Slot information during raid0 migration is displayed incorrectly
(missing disk position is taken from wrong map)
2. Improvement: information about (level, members, chunk size) migration is displayed.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Allow map related operations for the given map: first of second.
For reshape specific functionality it is required to have an access
Until now, the active map was chosen according to the current volume status.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>