syncthing/man/syncthing-networking.7
2015-08-16 15:29:48 +02:00

107 lines
3.3 KiB
Groff
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

.\" Man page generated from reStructuredText.
.
.TH "SYNCTHING-NETWORKING" "7" "August 13, 2015" "v0.11" "Syncthing"
.SH NAME
syncthing-networking \- Firewall Setup
.
.nr rst2man-indent-level 0
.
.de1 rstReportMargin
\\$1 \\n[an-margin]
level \\n[rst2man-indent-level]
level margin: \\n[rst2man-indent\\n[rst2man-indent-level]]
-
\\n[rst2man-indent0]
\\n[rst2man-indent1]
\\n[rst2man-indent2]
..
.de1 INDENT
.\" .rstReportMargin pre:
. RS \\$1
. nr rst2man-indent\\n[rst2man-indent-level] \\n[an-margin]
. nr rst2man-indent-level +1
.\" .rstReportMargin post:
..
.de UNINDENT
. RE
.\" indent \\n[an-margin]
.\" old: \\n[rst2man-indent\\n[rst2man-indent-level]]
.nr rst2man-indent-level -1
.\" new: \\n[rst2man-indent\\n[rst2man-indent-level]]
.in \\n[rst2man-indent\\n[rst2man-indent-level]]u
..
.SH PORT FORWARDS
.sp
If you have a NAT router which supports UPnP, the easiest way to get a working
port forward is to make sure UPnP setting is enabled on both Syncthing and the
router Syncthing will try to handle the rest. If it succeeds you will see a
message in the console saying:
.INDENT 0.0
.INDENT 3.5
.sp
.nf
.ft C
Created UPnP port mapping for external port XXXXX on UPnP device YYYYY.
.ft P
.fi
.UNINDENT
.UNINDENT
.sp
If this is not possible or desirable you should set up a port forward for port
\fB22000/TCP\fP, or the port set in the \fISync Protocol Listen Address\fP setting.
The external forwarded port and the internal destination port has to be the same
(i.e. 22000/TCP).
.sp
Communication in Syncthing works both ways. Therefore if you set up port
forwards for one device, other devices will be able to connect to it even when
they are behind a NAT network or firewall.
.SH LOCAL FIREWALL
.sp
If your PC has a local firewall, you will need to open the following ports for
incoming traffic:
.INDENT 0.0
.IP \(bu 2
Port \fB22000/TCP\fP (or the actual listening port if you have changed
the \fISync Protocol Listen Address\fP setting.)
.IP \(bu 2
Port \fB21025/UDP\fP (for discovery broadcasts on IPv4)
.IP \(bu 2
Port \fB21026/UDP\fP (for discovery multicasts on IPv6)
.UNINDENT
.SH REMOTE WEB GUI
.sp
To be able to access the web GUI from other computers, you need to change the
\fIGUI Listen Address\fP setting from the default \fB127.0.0.1:8384\fP to
\fB0.0.0.0:8384\fP\&. You also need to open the port in your local firewall if you
have one.
.SS Tunneling via SSH
.sp
If you have SSH access to the machine running Syncthing but would rather not
open the web GUI port to the outside world, you can access it through a SSH
tunnel instead. You can start a tunnel with a command like the following:
.INDENT 0.0
.INDENT 3.5
.sp
.nf
.ft C
ssh \-L 9999:localhost:8384 machine
.ft P
.fi
.UNINDENT
.UNINDENT
.sp
This will bind to your local port 9999 and forward all connections from there to
port 8384 on the target machine. This still works even if Syncthing is bound to
listen on localhost only.
.sp
You can forward multiple ports corresponding to many machines this way, but
because Syncthing uses session cookies for the entire domain (i.e. your local
machine), you will need to connect to each control panel in a separate browser
instance or explicitly issue a browser reload when switching between them.
.SH AUTHOR
The Syncthing Authors
.SH COPYRIGHT
2015, The Syncthing Authors
.\" Generated by docutils manpage writer.
.