This should address issue as described in https://forum.syncthing.net/t/stun-nig-party-with-paused-devices/10942/13
Essentially the model and the connection service goes out of sync in terms of thinking if we are connected or not.
Resort to model as being the ultimate source of truth.
I can't immediately pin down how this happens, yet some ideas.
ConfigSaved happens in separate routine, so it's possbile that we have some sort of device removed yet connection comes in parallel kind of thing.
However, in this case the connection exists in the model, and does not exist in the connection service and the only way for the connection to be removed
in the connection service is device removal from the config.
Given the subject, this might also be related to the device being paused.
Also, adds more info to the logs
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4533
This makes it OK to not have any listeners working. Specifically,
- We don't complain about an empty listener address
- We don't complain about not having anything to announce to global
discovery servers
- We don't send local discovery packets when there is nothing to
announce.
The last point also fixes a thing where the list of addresses for local
discovery was set at startup time and never refreshed.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4517
Well Tested(TM)
Introduces a potential issue where we always pick some connectable but dodgy connection that breaks
soon after the TLS handshake.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4489
This updates kcp and uses our own fork which:
1. Keys sessions not just by remote address, but by remote address +
conversation id 2. Allows not to close connections that were passed directly
to the library. 3. Resets cache key if the session gets terminated.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4339
LGTM: calmh
This adds a new config AllowedNetworks per device, which when set should
contain a list of network prefixes (192.168.0.0/126 etc) that are
allowed for the given device. The connection service will not attempt
connections to addresses outside of the given networks and incoming
connections will be rejected as well.
I've added the config to the normal device editor and shown it (when
set) in the device summary on the main screen.
There's a unit test for the IsAllowedNetwork method, I've done some
manual sanity testing on top of that.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4073
This adds support for AES_256_GCM_SHA384 (in there since Go 1.5, a bit
of a shame we missed it) and ChaCha20-Poly1305 (if built with Go 1.8;
ignored on older Gos).
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3822
The test for the error string is fragile, and the error string changed
in Go 1.8 so the relevant part is no longer a prefix. This covers it
with a test though, so it should be fine in the future as well.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3818
So there were some issues here. The main problem was that
model.Close(deviceID) was overloaded to mean "the connection was closed
by the protocol layer" and "i want to close this connection". That meant
it could get called twice - once *to* close the connection and then once
more when the connection *was* closed.
After this refactor there is instead a Closed(conn) method that is the
callback. I didn't need to change the parameter in the end, but I think
it's clearer what it means when it takes the connection that was closed
instead of a device ID. To close a connection, the new close(deviceID)
method is used instead, which only closes the underlying connection and
leaves the cleanup to the Closed() callback.
I also changed how we do connection switching. Instead of the connection
service calling close and then adding the connection, it just adds the
new connection. The model knows that it already has a connection and
makes sure to close and clean out that one before adding the new
connection.
To make sure to sequence this properly I added a new map of channels
that get created on connection add and closed by Closed(), so that
AddConnection() can do the close and wait for the cleanup to happen
before proceeding.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3490
Furthermore:
1. Cleans configs received, migrates them as we receive them.
2. Clears indexes of devices we no longer share the folder with
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3478
It seems that it would be impossible to drop down to relay after establishing a direct connection
Also, we should not drop the existing connection until after we've passed the validation steps,
and it seems it's being dropped in two places unnecesserily at the moment.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3480
This changes the BEP protocol to use protocol buffer serialization
instead of XDR, and therefore also the database format. The local
discovery protocol is also updated to be protocol buffer format.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3276
LGTM: AudriusButkevicius
Audrius Butkevicius
Jakob Borg
xjtdy888
Simon Frei
HairyFotr
Jakob Borg