Swap on video RAM
In the unlikely case that you have very little RAM and a surplus of video RAM, you can use the latter as swap.
MTD Kernel Subsystem
Potential benefits
A graphics card with GDDRX SDRAM or DDR SDRAM may be used as swap by using the MTD subsystem of the kernel. Systems with dedicated graphics memory of 256 MB or greater which also have limited amounts of system memory (DDRX SDRAM) may benefit the most from this type of setup.
- This will not work with binary drivers.
- Unless your graphics driver can be made to use less ram than is detected, Xorg may crash when you try to use the same section of RAM to store textures as swap. Using a video driver that allows you to override videoram should increase stability.
Pre-setup
You have to load the modules specifying the PCI address ranges that correspond to the RAM on your video card.
To find the available memory ranges run the following command and look for the VGA compatible controller section (see the example below).
$ lspci -vvv
01:00.0 VGA compatible controller: NVIDIA Corporation GK104 [GeForce GTX 670] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 8405 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 57 Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e8000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M] Region 5: I/O ports at e000 [size=128] [virtual] Expansion ROM at f6000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nouveau, nvidia
Of most potential benefit is a region that is prefetchable, 64-bit, and the largest in size.
A video card needs some of its memory to function, as such some calculations are needed. The offsets are easy to calculate as powers of 2. The card should use the beginning of the address range as a framebuffer for textures and such. However, if limited or as indicated in the beginning of this article, if two programs try to write to the same sectors, stability issues are likely to occur.
As an example: For a total of 256 MB of graphics memory, the formula is 2^28 (two to the twenty-eighth power). Approximately 64 MB could be left for graphics memory and as such the start range for the swap usage of graphics memory would be calculated with the formula 2^26.
Using the numbers above, you can take the difference and determine a reasonable range for usage as swap memory. leaving 2^24 (32M) for the normal function (less will work fine)
Setup
Configure the phram module (3.x kernels used the slram module):
/etc/modprobe.d/modprobe.conf
options phram phram=VRAM,0xStartRange,0xUsedAmount
Load the modules on boot:
/etc/modules-load.d/vramswap.conf
phram mtdblock
Create a systemd service:
/usr/lib/systemd/system/vramswap.service
[Unit] Description=Swap on Video RAM [Service] Type=oneshot ExecStart=/usr/bin/mkswap /dev/mtdblock0 ExecStart=/usr/bin/swapon /dev/mtdblock0 -p 10 ExecStop=/usr/bin/swapoff /dev/mtdblock0 RemainAfterExit=yes [Install] WantedBy=multi-user.target
mtdblock devices, use cat /proc/mtd to find the mtdblock with name VRAM.Xorg driver config
To keep X stable, your video driver needs to be told to use less than the detected videoram.
/etc/X11/xorg.conf.d/vramswap.conf
Section "Device"
Driver "radeon" # or whichever other driver you use
VideoRam 32768
#other stuff
EndSection
The above example specifies that you use 32 MB of graphics memory.
Troubleshooting
The following command may help you getting the used swap in the different spaces like disk partitions, flash disks and possibly this example of the swap on video ram
swapon -s
See also
FUSE filesystem
This method works on hardware with OpenCL support using a FUSE filesystem backing a swapfile. See GPGPU for more information.
Setup
First, install vramfs-gitAUR.
Then, create an empty directory as mount point (e.g /tmp/vram).
Now run the following commands to set up the vramfs and a swapfile.
# vramfs /tmp/vram 256MB -f # Substitute 256M with your target vramfs size # mkswap -U clear --size 200M --file /tmp/vram/swapfile # Substitute 200 with your target swapspace size in MiB
Your Swap should now be ready. Run swapon to check.
See Swap#Swap file for more information.
/tmp/vram as temporary storage, much like a Tmpfs.Setting swappiness
In the case of swap on VRAM, increasing swappiness may be a good idea. This is especially true when random I/O for the VRAM swapfile is significantly faster than random disk I/O, as the benefit of caching disk reads will outweigh the cost of swapping. For example, if your random disk I/O speed is the same as VRAM swap I/O, you should set swappiness to 100. If VRAM swap I/O is 2x faster than disk I/O, you should set swappiness to 133. See the kernel documentation for how to calculate the swappiness value correctly.
Troubleshooting
swapon: /tmp/vram/swapfile: skipping - it appears to have holes.
The swapfile created is not contiguous. A loop device can be set up to work around this issue.
# cd /tmp/vram # LOOPDEV=$(losetup -f) # truncate -s 4G swapfile # replace 4G with target swapspace size, has to be smaller than the allocated vramfs # losetup $LOOPDEV swapfile # mkswap $LOOPDEV # swapon $LOOPDEV
Complete system freeze under high memory pressure
Sometimes, under very high memory pressure, the vramfs process itself may get swapped to the VRAM swap space. This causes a complete deadlock. A fix is to make the process unswappable via cgroups by launching it via a systemd file:
/etc/systemd/system/vramswap.service
[Unit] Description=Set up swap in VRAM After=default.target [Service] Type=oneshot RemainAfterExit=yes # Change /root/vramswap.sh to a path to a script that performs all the necessary setup ExecStart=/root/vramswap.sh TimeoutStartSec=0 # Prevent swapping MemorySwapMax=0 [Install] WantedBy=default.target