Dell Vostro 1320

This article or section does not follow the Laptop page guidelines.

Reason: Stub (Discuss in Talk:Dell Vostro 1320)

This article or section is out of date.

Reason: This page is ancient (e.g. still references /arch/setup in #Installation. (Discuss in Talk:Laptop#Old laptop pages)

Hardware	PCI/USB ID	Working?
GPU (NVIDIA)		Yes
GPU (Intel)		Untested
Audio		Yes
Webcam		Yes
Fingerprint Reader		Untested
Card Reader		Yes
Wireless (Dell 1397)		Yes
Wireless (Dell 1510)		Yes
Wireless (Intel 5100)		Yes
Wireless (Intel 5300)		Yes
Bluetooth		Yes

This page is about setting up Arch Linux on the Dell Vostro 1320 laptop, which has replaced the former Dell Vostro 1310. Basically it runs just fine, although there are some things you should know. Furthermore it is advisable to read the article about laptops to get a idea about the topic in general.

Installation

It is highly recommendable to setup Windows Vista first, because during the setup the region code of the DVD drive is set.

If you want to install Arch Linux over a wireless connection you have to setup the connection manually. Since kernel 2.6.24 and above are containing the appropriate drivers already, it should work with both the "Netinstall ISO" as well as the "Core ISO", although using the "Netinstall ISO" is the preferred install media for Arch Linux. Do not forget to choose the source "net" and the wlan interface (normally wlan0).

Apart from that you can follow the Installation guide, which should deliver you a good insight how to install Arch Linux.

Further attention has to be drawn during the partitioning, as Dell uses an uncommon partition table, which may you run into some trouble. You will get a "FATAL ERROR", whenever you try to partition "/dev/sda" using the setup. Therefore switch to another terminal (Ctrl + Alt + F2, for instance) and delete the partition table using "fdisk /dev/sda". Follow the program options. More instructions can be found in the man page or the help option (m). It is sufficient to delete all partitions (and writing the table to the disc), from there on you can use the setup in the first terminal again (Ctrl + Alt + F1).

Note: When you remove all partitions the Dell Utility will not work anymore, so consider to leave the first partition, which contains the utility program. However the partition can be recreated. You can also run the diagnostic utility from an usb stick or a cd.

CPU

See CPU frequency scaling.

Audio

There is just a mono built-in speaker, do not wonder when you cannot balance the channel properly.

Fingerprint Reader

The Fingerprint Reader itself was not tested yet, but it should work following these steps.

Extra Keyboard Keys

Works using keytouchd. See Extra keyboard keys

Wireless

See Wireless network configuration.

Bluetooth

If your Vostro comes with Windows Vista installed (most of all), you need to update the Bluetooth driver in Windows Vista. Among other things, the driver changes the firmware of the module. Only after that Bluetooth will work under Linux.

Issues

Framebuffer

This article or section is out of date.

Reason: Rewritten in 2022 to link to KMS, since the Framebuffer page redirects to Uvesafb but the hardware from this system should work with KMS without additional configuration. (Discuss in Talk:Dell Vostro 1320)

You may experience some problems using the X server and console simultaneously, as soon as you work with different resolutions. In order to change the resolution of the console you should look at KMS. At the time of writing this page in 2009 adding vga=0x0361 to the /boot/grub/menu.lst worked.

Card Reader

Some cards may not be readable, in which case, dmesg will output the following lines:

[    8.790027] mmc0: error -110 whilst initialising SD card
[    8.790764] sdhci-pci 0000:1a:00.1: Will use DMA mode even though HW doesn't fully claim to support it.

This problem is easy to solve.Just add this line to your modprobe.conf

options sdhci debug_quirks=0x40

This will disable ADMA.